...

Gypsum Powder Ore Milling Equipment Maintenance


2018-01-04 13:48:50

Gypsum Powder Ore Milling Equipment Maintenance

Gypsum Powder Ore Milling Equipment Maintenance

After a long and high efficient operation, the Gypsum Powder Ore Milling Equipment wear will not only lose normally, but also the material fineness is not as good as before. In this paper, the working principle of the Gypsum Powder Ore Milling Equipment is taken as an entry point to analyze how to maintain the grinding effect.

Working principle of Gypsum Powder Ore Milling Equipment

3.jpg

The Ore Milling Equipment at work, material from the feed end of the hollow shaft into the cylinder when the rotating cylinder Ore Milling Equipment when grinding body due to inertia, centrifugal force and friction force, so that the material attached to the cylinder liner cylinder was taken away, when the material is brought to a certain height, due to its heavy force the dropped, the grinding body falling like a projectile like the material in the barrel to break. The material is evenly and evenly entered into the Gypsum Powder Ore Milling Equipment chamber through the feeding hollow shaft through the feeding device. There are stepped lining plates or corrugated lining plates in the warehouse, and different sizes of steel balls are mounted inside. The cylinder rotates to generate centrifugal force, which will bring the steel balls to a certain height and then fall down, which will cause heavy impact and abrasive effect on the materials. After the material is grinded in the silo, the material is entered into second storehouses through a single layer septum plate. The silo is inlaid with a flat plate with steel ball in the silo, and the material is further grinded. The powdery material is discharged through the discharge grate plate, and the grinding operation is completed.

How To Keep The Grinding Effect Of Gypsum Powder Ore Milling Equipment

  • 1. Some parameters of the opposing Ore Milling Equipment are adjusted. During the long run of the Gypsum Powder Ore Milling Equipment, due to the fineness, hardness and viscosity of the material are different, so the Gypsum Powder Ore Milling Equipment production capacity and abrasive medium will change to varying degrees. At this time, the size of the inlet and the size of the discharge port should be readjusted. If the Gypsum Powder Ore Milling Equipment lining is seriously worn or the one end has been broken, it is necessary to replace the new lining board in time. For the worn parts, users need to be replaced, otherwise the production will not be affected, nor the good grinding effect will be achieved.
  • 2, supplement the grinding medium. Gypsum Powder Ore Milling Equipment medium grinding ball is, after long time working, the grinding media will appear different degrees of wear, if it is not timely relief, in the Gypsum Powder Ore Milling Equipment for grinding material, grinding will appear insufficient fineness of grind unqualified, grinding uneven phenomenon, so the timely replenishment of grinding media is the foundation to maintain good grinding effect.
  • 4.jpg

The Ore Milling Equipment to maintain good grinding effect, there are many ways, such as according to the grinding processing ability of the reasonable control of feeding speed, to ensure uniform feed Ore Milling Equipment to prevent overload operation, ensure the grinding effect long-term efficient grinding Ore Milling Equipment; regular maintenance and cleaning, grinding storehouse, motor maintenance, bearing the lubrication and so on. There are many ways to keep the grinding effect on the ground, and the user can consult the customer service online free of charge.

...
Leave Message

...
Garnet Ore Milling Equipment 2018-01-04 13:48:50

Installation and maintenance of Garnet Ore Milling EquipmentThe maintenance of Garnet Ore Milling Equipment is a very important and regular job. It should coope

...
Cement Vertical Ore Milling Equipment 2018-01-04 13:48:50

How To Improve The Performance Of Cement Vertical Ore Milling EquipmentVertical Ore Milling Equipment in the coal mine is widely used, with China's economy and

...
T130X Strengthen Ultrafine Mill 2018-01-04 13:48:50

T130X Strengthen Ultrafine Mill, which is based on the market research, and statistically analyzes the user's usage and suggestions in many mills, and innovatin

...
Hammer Ore Milling Equipment With Cyclone 2018-01-04 13:48:50

How to choose Hammer Ore Milling Equipment With CycloneWith the market demand for a large number of mineral powder, the market appeared various types of Hammer

...
Ultra Fine Gold Quartz Ore Milling Equipment 2018-01-04 13:48:50

Ultra Fine Gold Quartz Ore Milling Equipment Basic IntroductionUltra Fine Gold Quartz Ore Milling Equipment is suitable for grinding ore materials have many kin

...
Micro Ore Milling Equipment 2018-01-04 13:48:50

Micro Ore Milling Equipment can be used for kaolin, limestone, calcite, marble, talc, barite, gypsum, dolomite, bentonite, mica, pyrophyllite, sepiolite, diatom



Categories
News